A documented food safety plan is a requirement under FDA FSMA regulations. Let’s go over what is required in all animal food safety plans, what is required under certain circumstances and what is recommended to be included in the plan.
Feed Mill and Feed Ingredient Requirements
Feed mills and feed ingredients suppliers in most cases do not need to implement all components of a Food Safety Plan. Food safety hazards at these types firms do not create the need for a specific preventive control, and most hazards can be managed through standard operating procedures.
Hazard Analysis – The Starting Point
A written hazard analysis is required for all animal food safety plans. A Hazard Analysis is defined by FDA as “the process of collecting and evaluating information about known or reasonably foreseeable biological, chemical (including radiological), and physical hazards associated with a food and the facility’s operations, in order to determine which hazards require a preventive control in the food safety plan. It must be documented in writing as part of the facility’s food safety plan, even if the outcome is that no hazards requiring a preventive control are identified”.
Hazard – Known or Reasonably Foreseeable?
To decide whether a hazard is known or reasonably foreseeable take the following into consideration:
-
Historical data and incident history for the food category (outbreaks, recalls, warning letters).
-
Scientific literature, trade association guidance, and FDA’s Guidance for Industry (GFI) #245: Hazard Analysis and Risk-Based Preventive Controls for Food for Animals.
-
Facility‑specific experience with non-conformances, complaints, environmental monitoring positive tests, and supplier performance.
Hazard – Severity and Probability of Happening
Once a hazard is identified for an ingredient or within a process step, the next step is to make a determination of the severity of the hazard and the probability of the hazard happening.
Severity
GFI #245 explains that, when assessing severity, the facility “should consider certain factors” such as:
-
Susceptibility of the animal species (e.g., species more sensitive to a toxin or nutrient imbalance).
-
Nature of the health effect: death, permanent disability, long‑term impairment, or transient/reversible illness.
-
Whether humans could be affected through handling pet food in the home or consuming meat, milk, or eggs from food-producing animals exposed to the hazard.
Probability
GFI #245 explains that, after identifying known or reasonably foreseeable hazards, the facility must evaluate “the probability that the hazard will occur in the absence of preventive controls” as part of deciding whether it is a hazard requiring a preventive control. This evaluation is done for each hazard at each relevant point (ingredient, process step, environment, etc.), not once for the product as a whole.
FDA expects this to be an evidence‑based professional judgment by the PCQI. The method can be qualitative as long as the reasoning is clear and consistent.
GFI #245 and FSPCA (Food Safety Preventive Controls Alliance) materials describe several factors facilities should consider when estimating likelihood:
-
Historical information: past test results, deviation records, complaints, or incidents for that product, ingredient, or process in your facility or the industry.
-
Product and process characteristics: whether the step or ingredient tends to introduce or support the hazard (e.g., raw vs heat‑treated, moisture, time/temperature, cross‑contamination potential).
-
Facility conditions: design, traffic patterns, environmental exposure, pest pressure, and sanitation practices that make introduction or growth more or less likely.
-
Supplier and prerequisite program strength: robustness of supplier approval, COAs, GMPs, sanitation, and other programs that already reduce the probability of occurrence.
Evaluating Severity and Probability
Most firms use a hazard matrix that “scores” the combination of probability with severity to determine if a Preventive Control is needed. A firm has much greater influence over the probability of a hazard occurring versus influencing the severity of an ingredient or process step. That is because if a firm is following FDA Current Good Manufacturing and a comprehensive set of Standard Operating procedures, it will be able to make a strong case for a low probability of occurrence for given hazards.
No Preventive Controls Needed-What’s Not Required?
The following parts of a Food Safety Plan are not required when a preventive control has not been identified in the Hazard Analysis.
Preventive Controls
- Supply-chain applied controls
- Process Controls
- Sanitation Controls
- “Other” Controls
Preventive Control Management Components
- Monitoring
- Corrective Actions and Corrections
- Verification
- Validation
- Verification of implementation and effectiveness
- Recall Plan
Pet food and treat manufacturers will need to comply with the additional steps listed above as they typically have at least one Preventive Control identified in their Hazard Analysis.
Keeping the Food Safety Plan Current
There needs to be a reanalysis of the Food Safety Plan when the following occurs
-
At least once every 3 years, the Food Safety Plan as a whole must be reanalyzed by or under the oversight of a Preventive Controls Qualified Individual. Note: Guidance emphasizes that this 3‑year review is a minimum; firms may choose more frequent internal reviews as a best practice.
-
Whenever a significant change in activities at the facility creates a reasonable potential for a new hazard or significantly increases a previously identified hazard (e.g., new product line, process, or equipment).
-
When the facility becomes aware of new information about potential hazards or preventive controls for its animal food (e.g., new science, new outbreak or contaminant of concern).
-
When appropriate after an unanticipated food safety problem that requires a corrective action (e.g., contamination event, recall, or regulatory finding about ineffective controls).
-
Whenever a preventive control, combination of controls, or the Food Safety Plan as a whole is found to be ineffective.
-
Reanalysis is also required when FDA determines it is necessary to respond to new hazards and developments in scientific understanding, and the agency notifies firms of that determination.
Best Practices - Additional Items for the Food Safety Plan
Some recommended documents for any Food Safety Plan include:
- List of Food Safety Team members if one has been established
- A process flow diagram
- Overview of the facility including information; such as, years in business, hours of operation, number of employees, types of animal food manufactured and for what species of animal and geographic areas served.
Final Thoughts
A well-executed hazard analysis supported by strong food safety procedures is your best defense and determines what if anything else is needed for the Food Saafety Plan.

